Crossover Frequency: 2.1kHz Nominal Impedance: 8 Ohms Skretnica za 10 inca bas i 1-1.4 inca visokotonac.

Key features 98 dB SPL 1W / 1m average sensitivity 8 ohms 100 mm (4 in) Interleaved Sandwich Voice coil (ISV) 2400 W program power handling Triple Silicon Spider (TSS) for superior excursion control and linearity Double Demodulating Rings (DDR) for lower distortion Improved heat dissipation via integrated air diffractor and multiple backplate vents Weather protected cone and plates for outdoor usage Description The 18LW2400 is an 18 inch extended low frequency loudspeaker designed for high SPL subwoofer applications in either a reflex, bandpass or horn loaded configuration. Compared to our industry standard 18LW1400, the 18LW2400 provides higher maximum SPL, increased program power handling and lower power compression. For optimum results we recommend amplifiers able to deliver 2400 Watt program power without clipping. Transducer design features include a large displacement suspension system which, in conjunction with a fiberglass reinforced, straight ribbed cone and the Eighteen Sound proprietary Triple Silicon Spider (TSS) technology, allows an ultra-linear piston action and provides full mechanical control across the entire working range. The 100 mm (4 in) inside-outside copper voice coil based on Interleaved Sandwich Voice coil (ISV) technology provides high levels of thermal stability and durability. In order to furtherly increase power handling and reduce power compression figure, 18LW2400 uses the same voice coil ventilation technology developed for our flagship 9000 neodymium transducer series. A special low density material air diffractor has been placed into the backplate acting as a cooling system, increasing power handling capability and lowering the power compression figure. As a final result Eighteen Sound engineers obtained almost 1 dB reduction in full power power compression value if compared to 18LW1400, and an increased program power handling value of 2400 Watt. The low distortion and unmatched sound quality of the 18LW2400 has been significantly improved by Double Demodulating Rings (DDR) embedded in the pole piece of the magnetic structure. These have been designed to reduce the intermodulation and harmonic distortion while improving the transient response. 10% reduction in weight have been obtained optimizing the magnetic structure through advanced FEA CAD simulation tools. 18LW2400 is able to perform properly under inclement weather conditions: the exclusive cone treatment improves pulp strength and gives water repellent properties to both sides of the cone. In addition, the special treatment applied to top and back plates of the magnetic structure is far more resistant to the corrosive effects of salts and oxidization.

For optimum results we recommend amplifiers able to deliver 2600 Watt program power without clipping. Transducer design features include a large displacement suspension system which, in conjunction with a fiberglass reinforced, straight ribbed cone, allows an ultra-linear piston action and provides full mechanical control across the entire working range. The 100 mm (4 in) inside-outside copper voice coil based on Interleaved Sandwich Voice coil (ISV) technology provides high levels of thermal stability and durability. In order to furtherly increase power handling and reduce power compression figure, 18LW2420 uses the same voice coil ventilation technology developed for our flagship 9000 neodymium transducer series. A special low density material air diffractor has been placed into the backplate acting as a cooling system, increasing power handling capability and lowering the power compression figure. The low distortion and unmatched sound quality of the 18LW2420 has been significantly improved by Single Demodulating Ring (SDR) embedded in the pole piece of the magnetic structure. These have been designed to reduce the intermodulation and harmonic distortion while improving the transient response. The magnetic structure has been optimized through advanced FEA CAD simulation tools. 18LW2420 is able to perform properly under inclement weather conditions: the exclusive cone treatment improves pulp strength and gives water repellent properties to both sides of the cone. In addition, the special treatment applied to top and back plates of the magnetic structure is far more resistant to the corrosive effects of salts and oxidization. Specifications Nominal Impedance8 Ω Nominal Power Handling11300 W Continuous Power Handling22600 W Sensitivity397.0 dB Frequency Range30 - 2500 Hz Voice Coil Diameter100 mm (4.0 in)

Eminence PXB 33K5 Designed to work in high-power cabinets, px crossovers are technically superior passive filters available as board-only or complete with fitted hardware for a smart, economical 'factory-fit' finish. Designed and built for Eminence, px crossovers feature Specification Type 3-way Cabinet Ready?* No Crossover Frequency 500Hz/3.5kHz Slope 12dB/octave LP Impendance 8 ohms Power Handling 400W HF Level ~ Mounting cut-out ~

Crossover for 2-way system Crossover Freq.: 7kHz Slope: 12dB/oct. Power RMS: 100W Connectors: none

Ferrite LF-MB-MF Transducers Extended Low Frequency Transducer Key Features 96 dB SPL 1W / 1m average sensitivity 75 mm (3 in) Interleaved Sandwich Voice coil (ISV) 500 W AES power handling Double Silicon Spider (DSS) for improved control and linearity Improved heat dissipation via unique basket design Weather protected cone and plates for outdoor usage Ideal for compact reflex subwo Description The 12LW800 is a low frequency loudspeaker which sets a new industry standard in 12" (300mm) Ø high performance transducers, achieving a remarkable 42Hz downwards extension with 96dB average sensitivity, handling peak power levels of 4000W with remarkably low distortion and excellent transient response. The 12LW800 is intended as the low bass or sub-woofer component, either in highly compact reflex, bandpass or horn loaded configurations, to provide clean, linear frequency reproduction at high power levels, or as part of a compact high power fullrange system. In its reflex configuration it can be used in extremely compact enclosures (40 - 70lt) making it ideally suited to portable applications such as road shows and bass musical instruments, for “wedge” stage monitors, etc. The high excursion capabilities of the double-action roll surround and suspension system, in conjunction with the Eighteen Sound Double Silicon Spider (DSS), has enabled the 12LW800 to achieve very high levels of linear travel for a 12" unit. The carbon fibre reinforced curvilinear ribbed cone, with its custom design surround, assures smooth response and exceptional strength with maximum reliability under high mechanical stress. The 75mm Ø state-of-the-art voice coil is similar to that fitted to our 18LW1400 top-of-the-range model. It employs our Interleaved Sandwich Voice coil (ISV) in which a high strength fiberglas former carries windings on both the outer and inner surfaces to achieve a mass balanced coil and providing a uniform motive drive. This, in conjunction with the use of unique high temperature resin adhesives, results in an extremely linear motor assembly with reduced tendency to break-up under high drive conditions. Excellent heat dissipation is achieved by the incorporation of air channels between the basket and top plate. Maximum flux concentration and force factor in the gap is assured by the unique shape and design of the face and back plates, these having been researched and designed using our in-house Magnetic Flux FEA CAD resource. With the increasing use of high power audio systems at outdoor events or in a marine environment, the ability to perform properly under inclement weather conditions is another part of the Eighteen Sound philosophy. This is achieved by means of an exclusive cone treatment improving pulp strength and giving water repellent properties to the cone. In addition, special treatment of both the face and back plates results in a product which is far more resistant to the corrosive effects of salts and oxidisation than any other treatment in use. General Specifications Nominal Diameter 300 mm (12 in) Rated Impedance 8 Ohm AES Power 500 W Program Power 800 W Peak Power 4000 W Sensitivity 96 dB Frequency Range 46 ÷ 4200 Hz Power Compression @-10dB 0,9 dB Power Compression @-3dB 2,6 dB Power Compression @Full Power 4 dB Max Recomm. Frequency 1300 Hz Recomm. Enclosure Volume 40 ÷ 100 lt. (1,41 ÷ 3,53 cuft) Max Peak To Peak Excursion 34 mm (1,34 in) Voice Coil Diameter 75 mm (2,95 in) Voice Coil Winding Material copper Suspension Single roll, rubber Cone Curvilinear ribbed, Paper Thiele Small Parameters Fs 52 Hz Re 5,6 Ohm Sd 0,0531 sq.mt. (82,31 sq.in.) Qms 7,6 Qes 0,3 Qts 0,29 Vas 48 lt. (1,70 cuft) Mms 76,5 gr. (0,17 lb) BL 21,3 Tm Linear Mathematical Xmax ± 6,5 mm (± 0,26 in) Le (1kHz) 1,72 mH Ref. Efficiency 1W@1m (half space) 95,5 dB Mounting information Overall diameter 315 mm (12,4 in) N. of mounting holes and bolt 8 Mounting holes diameter 7,15 mm (0,28 in) Bolt circle diameter 296 - 300 mm (11,65 - 11,8 in) Front mount baffle cutout ø 282 mm (11,1 in) Rear mount baffle cutout ø 282 mm Total depth 151 mm (5,94 in) Flange and gasket thickness 20 mm (0,79 in) Flange and gasket thickness 20 mm (0,79 in) Net weight 8,1 kg (17,88 lb) Shipping weight 8,9 kg (19,65 lb) CardBoard Packaging dimensions 332 x 332 x 184 mm (13,07 x 13,07 x 7,24 in)

The deep profile curvilinear cone, made with high strength wood pulp, has been designed to achieve the best possible linearity within its frequency range. The cone surround, made from a linen material, is highly resistant to aging and fatigue. The in-house developed cone treatment is humidity repellent and significantly dampens bell mode resonances. The 75mm (3in) copper edge-wound voice coil assembly is wound on a strong fiberglas former to improve force transmission and power handling. The already low distortion and high sound quality are further improved by the aluminum demodulating ring (SDR) used to reproduce instantaneous peak on mid frequencies, reducing intermodulation distortion. The magnetic structure has been optimized using our FEA CAD software that has maximized the flux density in the voice coil gap. Excellent heat dissipation has also been achieved by incorporating air channels between the basket and the magnetic top plate. Due to the increase in use of audio systems at outdoor events, the ability of the 15W930 to perform in adverse weather conditions or in areas of high humidity is a great advantage. This has been achieved using exclusive treatments which enable the cone and the magnetic plate to resist corrosion and render the cone water repellent at the same time. General Specifications Nominal Diameter 380 mm (15 in) Rated Impedance 8 Ohm AES Power 500 W Program Power 800 W Peak Power 1600 W Sensitivity 98 dB Frequency Range 50 ÷ 3600 Hz Power Compression @-10dB 0,6 dB Power Compression @-3dB 1,9 dB Power Compression @Full Power 2,8 dB Max Recomm. Frequency 1700 Hz Recomm. Enclosure Volume 60 ÷ 140 lt. (2,12 ÷ 4,95 cuft) Minimum Impedance 7,2 ohm at 25°C Max Peak To Peak Excursion 33 mm (1,30 in) Voice Coil Diameter 75 mm (3 in) Voice Coil Winding Material Edgewound Copper Suspension M-roll, Polycotton Cone Curvilinear, humidity repellent Thiele Small Parameters Fs 33 Hz Re 5,5 Ohm Sd 0,086 sq.mt. (132.53 sq.in.) Qms 8,78 Qes 0,23 Qts 0,22 Vas 240 lt. (8,46 cuft) Mms 97 gr. (0,21 lb) BL 22,1 Tm Linear Mathematical Xmax ± 7,5 mm (± 0,30 in) Le (1kHz) 1,47 mH Ref. Efficiency 1W@1m (half space) 97,9 dB Mounting information Overall diameter 393 mm (15,47 in) N. of mounting holes and bolt 8 Mounting holes diameter 7,15 mm (0,28 in) Bolt circle diameter 371 mm (14,6 in) Front mount baffle cutout ø 360 mm (14,17 in) Rear mount baffle cutout ø 354 mm (13,94 in) Total depth 185 mm (7,28 in) Flange and gasket thickness 14 mm (0,55 in) Net weight 7,6 kg (16,7 lb) Shipping weight 9,1 kg (20,06 lb) CardBoard Packaging dimensions 405 x 405 x 252 mm (15,94 x 15,94 x 9.92 in)

Eighteen Sound 18TLW3000, 8ohm 3600 W program power handling 100 mm (4 in) Tetracoil dual voice coil, equivalent to a single coil diameter larger than 152 mm (> 6 in) Ultra linear suspension behavior for excellent sound clarity Symmetric flux density and inductance behaviour Low noise forced air cooling design Water repellent cone and epoxy coated plates for outdoor use Suitable for vented, horn loaded and bandpass subwoofer designs Designed & manufactured in Italy and provided exclusively by Lean

Speaker grill 20cm/8"

Nominal diameter: 381mm / 15in Power rating: 250W Continuous power rating: 500W EIA power rating: 400W Rated impedance: 8Ω Sensitivity: 98dB Frequency range: 40-3000Hz Chassis type: Pressed steel Magnet type: Ferrite Magnet weight: 1.2kg / 42oz Voice coil diameter: 64mm / 2.5in Voice coil material: Round copper Former material: Polyimide Cone material: Kevlar loaded paper Surround material: Cloth-sealed Suspension: Single Gap height (Hg): 8mm / 0.31in VC winding height (Hvc): 13mm / 0.51in

Professional 2-way crossover Crossover Freq.: 1,8kHz Slope: 12dB/oct. Power RMS: 300W Connectors: 2 x Speakon®

Nominal diameter: 381mm / 15in Power rating: 300W Continuous power rating: 600W EIA power rating: 450W Rated impedance: 8Ω Sensitivity: 97dB Frequency range: 45-3500Hz Chassis type: Pressed steel Magnet type: Ferrite Magnet weight: 1.4kg / 50oz Voice coil diameter: 64mm / 2.5in Voice coil material: Edgewound copper Former material: Glass fibre Cone material: Kevlar loaded paper Surround material: Cloth-sealed Suspension: Single Gap height (Hg): 8mm / 0.31in VC winding height (Hvc): 14.5mm / 0.57in Additional impedances: 4Ω

HF Compression Driver 8 Ohm · 1 inch exit throat · 106 dB SPL 1W / 1m average sensitivity · 34,4 mm (1 1/3 inch) voice coil diameter · 60 Watt program power handling · Titanium diaphragm · Proprietary phase plug design · Usable in two way or multiway systems The HD1030 1 inch exit high frequency compression driver has been designed for use in two-way audio systems. The transducer exhibits a constant slope response from 1.5kHz to 18kHz with a uniform and smooth roll-off. With a 800 Hz free air resonance frequency, the HD1030 can easily be cut-off at 1800Hz and is capable of 60W continuous power handling with a 1800Hz pink-noise signal, and a 6dB crest factor with a minimum 12dB/oct crossover slope. Equipped with unique Phase Plug architecture, the HD1030 has been designed to give a smooth coherent wavefront at the horn entrance in the whole working frequency range, as well as high level manufacturing consistency. The phase plug with its short openings and high flare rate value assures low distortion and demonstrates remarkable improvements in mid-high frequency reproduction. The titanium diaphragm assembly, with its ellipsoidal suspension shape, exhibits a constant slope response from 1.5kHz up to 18kHz with uniform smooth roll-off behavior. An edge-wound aluminum voice coil, wound on proprietary treated Nomex, completes the diaphragm assembly. Nomex shows a 30% higher value of tensile elongation at a working operative temperature (200°C) when compared to Kapton. This feature enables proper energy transfer control from the voice coil to the dome in real working conditions. Moreover, this proprietary former material is also suitable for use in higher moisture content environments. The HD1030 powerful ceramic magnet assembly has been designed to obtain 15 KGauss in the gap within a compact ferrite motor structure. GENERAL SPECIFICATIONS Throat Diameter 25,4 mm (1 in) Rated Impedance 8 ohm DC Resistance 5,8 Ohm Minimum Impedance 6,5 Ohm at 5000Hz Le (at 1kHz) 54 µH AES power 30 W above 2 kHz Program power 60 W above 2 kHz Sensitivity(1W@1m) 106 dB Frequency Range 1800Hz ÷ 20kHz Recomm. Xover Frequency 1800Hz Diaphragm Material Titanium Voice Coil Diameter 34,4 mm (1 1/3 in) Voice Coil Winding Material Edge-wound aluminum Magnet Material Ferrite Flux Density 1,5 T BL Factor 5 N/A Polarity Positive voltage on red terminal gives positive pressure in the throat MOUNTING INFORMATIONS Overall diameter 91 mm (3.6 in) Mounting holes diameter 4 M5 holes on Ø 76 mm (3 in) Bolt circle diameter 76 mm (3 in) Total depth 51 mm (2 in) Net weight 1 kg (2.18 lb) Shipping weight 1.2 Kg (2.61 lb) CardBoard Packaging dimensions 97x97x58 mm (3,8x3,8x2,3 in) HD1030 MEASURED WITH 1W INPUT ON RATED IMPEDANCE AT 1M DISTANCE ON XT1086 HORN MOUTH AXIS FREE AIR IMPEDANCE MAGNITUDE CURVE

The 1530 is a high performance bass and mid range driver. It has a large magnet, resulting in a high Bl product, with high sensitivity and power handling. General specifications Nominal diameter (mm/in) 381/15 Power Rating (AES, W rms) 400 Nominal impedance (�) 8 Voice coil diameter (mm/in) 76/3 Magnet type Ceramic Magnet weight (kg/oz) 2.44/86 Chassis type Pressed steel Sensitivity (dB) 99 Frequency range (Hz) 40-3000 Coil material Round copper Former material Polyimide Cone material Kevlar loaded paper Surround material Cloth-sealed Suspension Single Xmax (mm/in) 2.0/0.08 Gap depth (mm/in) 8.0/0.31 Voice coil winding width (mm/in) 12.0/0.47 Small Signal Parameters D (m/in) 0.33/12.99 Fs (Hz) 45 Mmd (g/oz) 77.70/2.74 Mair Qms 4.20 Qes 0.42 Qts 0.38 Re (�) 5.70 Vas (lt/ft3) 141.2/4.99 BI (Tm) 18.70 Cms (mm/N) 0.14 Rms (kg/s) 6.13 Le (mH) Mounting Information Overall diameter (mm/in) 385/15.16 Overall depth (mm/in) 163/6.42 Cut-out diameter (mm/in) 352/13.86 Mounting slot dimensions (mm/in) 9.2 x 6.2/0.36 x 0.24 Number of mounting slots 8 Mounting slot PCD range (mm/in) 369/14.56 Unit weight (kg/lb) 6.1/13.4 Packed Dimensions and Weight Single pack size W x D x H (mm/in) 410 x 410 x 180/16.1 x 16.1 x 7.1 Single pack weight (kg/lb) 8/17.6 Multipack (45) size W x D x H (mm/in) 1200 x 1000 x 980/47.2 x 39.4 x 38.6 Multipack (45) weight (kg/lb) 370/816

Frequency Response and Impedance Curves Tested for two hours using a continuous, band-limited pink noise signal as per AES standard. Power calculated on minimum impedance. Loudspeaker tested in free air. Continuous Power Rating is defined as 3dB greater than the AES rating. Tested as per the EIA-426-A standard. Measured on axis at 1W, 1m in 2Π anechoic environment. Xmax derived from: (voice coil winding width-gap depth)/2. Small signal parameters measured after unit subjected to pre-conditioning signal. General Specifications Nominal diameter 127mm/5in Power rating1 30Wrms Continuous power rating2 60W EIA power rating3 50W Nominal impedance 8Ω Sensitivity4 91dB Frequency range 130-8,000Hz Voice coil diameter 25mm/1in Chassis type Pressed steel Magnet type Ferrite Magnet weight 0.37kg/13oz Coil material Round copper Former material Polyimide Cone material Kevlar loaded paper Surround material Cloth-sealed Suspension Single Xmax5 1.1mm/0.04in Gap depth 5mm/0.20in Voice coil winding width 7.3mm/0.29in Small Signal Parameters D 0.10m/3.94in Fs 128.1Hz Mms 7.02g/0.25oz Qms 2.376 Qes 0.768 Mmd 5.3g/0.187oz Qts 0.6580 Re 6.32Ω Vas 7.38lt/0.26ft3 BI 6.82Tm Cms 0.22mm/N Rms 2.38kg/s Le (at 1kHz) 0.33mH Mounting Information Overall diameter 136 x 151mm/5.35in x 5.94in Overall depth 68mm/2.68in Cut-out diameter 117mm/4.61in Mounting slot dimensions Ø 4.5mm/0.18in Number of mounting slots 4 Mounting PCD range 140mm/5.51in Unit weight 1.0kg/2.2lb Packed Dimensions & Weight Single pack size W x D x H 170mm x 180mm x 70mm /6.7in x 7.1in x 2.8in Single pack weight 1.5kg/3.3lb Multi pack size W x D x H 320mm x 550mm x 190mm /12.6in x 21.7in x 7.5in Multi pack weight 15kg/33lb

NOMINAL SPECIFICATIONS Nominal diameter 380 mm (15 in) Maximum External Diameter 393 mm (15.47 in) Distance between fixing holes 374 mm (14.72 in) Recess Hole Diameter 356 mm (14.02 in) Depth 165 mm (6.50 in) Flange and Gasket Thickness 13.1 mm (0.52 in) TECHNICAL PARAMETERS Nominal Impedance 8 Ohms Rated Power (AES) (1) 400W Maximum Power (2) 800W Efficiency (1W/1m) 99dB Frequency Range 35÷4000 Hz Coil diameter 77 mm (3 in) Support Material Glass fiber Winding Height 15 mm (0.59 in) Air gap height 10.5 mm (0.41 in) Flux Density 1.15T Magnet Type Neodymium pad Basket material Aluminum

Size:8 inch Rate Impedance: 8Ω Rate Power:200W Voice coil:51mm/2 inch Magnet:140mm fequency range.64.5-5.2KHz

General Specifications Power rating1 20Wrms Nominal impedance 8Ω Frequency range 2000-20,000Hz Sensitivity2 104dB Recommended min. crossover (12dB/oct) 2500Hz Voice coil diameter 35mm/1.4in Voice coil material Copper clad aluminium Magnet type Neodymium Diaphragm material Aluminium Surround material Elastomer Mounting Information Overall width 90mm/3.5in Overall depth 57mm/2.2in Fitting Flange (2 x M6 holes on 76mm, 3.0in PCD) Throat exit 25.4mm/1in Unit weight 0.25kg/0.6lb Packed Dimensions & Weight Single pack size W x D x H 90mm x 90mm x 60mm /3.5in x 3.5in x 2.4in Single pack weight 0.5kg/1.1lb Multi pack (24) size W x D x H 250mm x 350mm x 290mm /9.8in x 13.8in x 11.4in Tested for two hours on plane wave tube using a continuous, band-limited pink noise signal as per AES standard. Power calculated on minimum impedance. Measured on axis at 1W, 1m, using typical horn, in 2π anechoic environment

6ND430 LF Neodymium Driver Key features 92,5 dB SPL 1W / 1m average sensitivity 45 mm (1,77 in) aluminum voice coil 200 W AES power handling Neodymium motor assembly Weather protected cone Improved heat dissipation via unique basket design Ideal for compact two way and multiway systems Downloads Data sheet Drawing 022066N430-6ND430-16.pdf Description The 6ND430 is a 6 inch neodymium woofer designed for low frequency reproduction in 2-way systems or multiway systems where both low weight and high intelligibility are required. The speaker has been specifically designed for compact reflex enclosures where high quality low-bass and mid frequencies are required such as studio monitoring applications. It is also currently used in line array or multiway systems with excellent results. The extremely powerful external neodymium magnet assembly assures high flux concentration, low power compression and excellent heat exchange. The levels of force factor and power handling are, as a consequence, at a top professional level with an optimum power to weight ratio. A consistent heat transfer is guaranteed by the encapsulation of the magnetic structure in the interior of the basket, offering a large contact space between the back plate and the dissipating structure. Particular effort was given to the surround shape and material design in order to minimise the resonances on mid range frequencies. The new design, realised with specified rubber based material density, offers a consistent dampening to typical bell modes. The 45 mm voice coil is made from a light-weight aluminum wire and assures linearity and high power handling. A proprietary humidity-block cone treatment makes the transducer suitable for outdoor use in adverse weather conditions. In addition, a special coating applied to both the top and back plates makes the 6ND430 far more resistant to the corrosive effects of salts and oxidization. GENERAL SPECIFICATIONS Nominal Diameter 152mm (6 in) Rated Impedance 8 Ohm AES Power 200 W Program Power (1) 260 W Peak Power (2) 500 W Sensitivity (3) 92,5 dB Frequency Range (4) 63 ÷ 5500 Hz Power Compression @-10dB (5) 1,0 dB Power Compression @-3dB 1,5 dB Power Compression @Full Power 2,9 dB Max Recomm. Frequency 3000 Hz Recomm. Enclosure Volume 10 ÷ 40 lt. (0,35 ÷ 1,41 cuft) Minimum Impedance 6,1 Ohm at 25°C Max Peak To Peak Excursion 22 mm (0,87 in) Voice Coil Diameter 44 mm (1,75 in) Voice Coil Winding Material aluminum Suspension Single roll, Rubber Cone Curvilinear, Paper THIELE SMALL PARAMETERS (6) Fs 61 Hz Re 5.5 Ohm Sd 0,0133 sq.mt. (20,6 sq.in.) Qms 6.5 Qes 0.28 Qts 0.27 Vas 12.6 lt. (0,4 cuft) Mms 13,3 gr. (0,03 lb) BL 10.0 Tm Linear Mathematical Xmax (7) ± 5 mm (±0,20 in) Le (1kHz) 0.28 mH Ref. Efficiency 1W@1m (half space) 92 dB MOUNTING INFORMATIONS Overall diameter 162 mm (6,38 in) N. of mounting holes 4 Mounting holes diameter 5,5 mm (0,22 in) Bolt circle diameter 170 mm (6,69 in) Front mount baffle cutout ø 148 mm (5,38 in) Rear mount baffle cutout ø 148 mm (5,38 in) Total depth 73 mm (2,87 in) Flange and gasket thickness 9,5 mm (0,37 in) Net weight 1,25 kg (2,76 lb) Shipping weight 1,8 kg (3,97 lb) CardBoard Packaging dimensions 170 x 170 x 80 mm (6,69 x 6,69 x 3,15 in) FREQUENCY RESPONSE CURVE OF 6ND430 MADE ON 18 LIT. ENCLOSURE TUNED AT 60HZ IN FREE FIELD (4PI) ENVIRONMENT. ENCLOSURE CLOSES THE REAR OF THE DRIVER. THE THIN LINE REPRESENTS 45 DEG. OFF AXIS FREQUENCY RESPONSE FREE AIR IMPEDANCE MAGNITUDE CURVE

Rubber base for speaker cabinet

The HD2000 1.4 inch exit high frequency compression driver has been designed for use in high quality audio systems. The titanium diaphragm is produced in-house and has been developed to assure unmatched transient response. A proprietary treated Nomex former with edge-wound copper-clad aluminum wire (CCAW) 60mm voice coil completes diaphragm assembly. It has been made by joining the proprietary-treated Nomex former directly to the titanium dome through its upper bend edge. In comparison with a usualstraight former joint, the driver design assures extended frequency energy transfer for improved response linearity and unparalleled reliability. This feature maintains proper motion control of the dome in real working conditions. Due to its physical properties, the proprietary-treated Nomex former shows a 30% higher value of tensile elongation at working operative temperatures (200°C) when compared to Kapton. Moreover, thismaterial issuitable to work also in highermoisture-content environments. Equipped with Proprietary Phase Plug 3P architecture, the HD2000 has been designed to give a smooth coherent wave front at the horn entrance in all working frequency ranges with a high level manufacturing consistency. The phase plug with its short openings and high flare rate, assureslow distortion with excellent mid-high frequency reproduction. The HD2000 powerful ceramic magnet assembly has been designed to obtain 16 kGauss in the gap within a compact ferrite motor structure. The motor structure is equipped with copper ring on the pole piece, reducinginductance effect and distortion. General Product type : Compression driver Brand : Eighteen Sound Manufacturer reference : HD2000 Product code : DRV142000TI08FA - 0421T8H200 Informations Nominal impedance : 8 ohm Dimensional category : 6 inch Manufacturer sensitivity : 108 dB Nominal power handling : 70 W Max power handling : 140 W Bandwidth : 1000÷20000 Hz Recommended min cutoff frequency : 1000 Hz Exit diameter compression driver : 1.4 inch Datas Flux density : 1.6 T Zmin : 7.6 ohm Weight : ~2.8 kg Dimensions Voice coil diameter : 2.4 inch Outside diameter : 145 mm Depth : 65 mm Shape & Materials Front chape : Cylindrical Magnet type : Ferrite

Nominal Diameter: 460 mm (in) Nominal Impedance: 8 Ω Minimum Impedance: 6.4 Ω Nominal Power Handling1: 1000 W Continuous Power Handling2: 1400 W Sensitivity3: 98.0 dB Frequency Range: 35 - 3500 Hz Voice Coil Diameter: 100 mm (4.0 in)